Applies to: Giza
This article explains the following Giza wall editing functions: Corner editor, Fillet, Chamfer, Trim, Extend, and Stretch.
To discuss and demonstrate the corner editor, fillet, and chamfer functions, it will be helpful to begin by drawing these four wall configurations. The dimensions of the walls are not important, but creating the below example configurations will help you follow along with each of the examples below. Expand the commands below to learn more of each function.
Corner Editor
Using the corner editor, you can connect two non-intersecting walls to form a corner (Seen in example 1 image above) or you can take two walls that are crossing and create a clean corner connection (Seen in example image 2 above).
- On the Walls icon menu under the section called Wizards, click the Corner Editor icon.
- At the bottom of the drawing window, in the status bar, will be a prompt asking you to select the intersection of the walls you want to edit. Left click on the right side of the horizontal line in the example 1 layout. The Visual Wall Corner Editor dialog appears with a graphic preview of the corner that has been selected.
- Make sure the radio button is set to Corner. In the graphic preview, a closed corner is represented by yellow lines.
- Click Apply. The two walls should now be joined forming a corner.
5. Clicking the Select button on the Corner Editor dialog will let you select another wall. In the example 2 layout, we have two walls that are crossing each other we need to make into a clean corner. Click Select and then click on the wall segment portion that is not needed.
6. The preview of the closed corner will be represented by yellow lines and will clean up the excess wall segments. If the output in preview is not the desired corner, click Select again, and click on one of the other wall segments until you get the desired preview result.
7 Click Apply and, in this example, the corner editor will remove the excess wall segments to create a clean corner.
Fillet
Using the corner editor, you can also round a corner to a chosen radius.
- Click the Corner Editor icon.
- Click on the corner in the example 3 layout, which is the corner to be curved.
- In the Visual Wall Corner Editor dialog, set the radio button to Fillet.
- Enter the radius of the curve.
- Look at the preview in the dialog.
- Click Apply.
Chamfer
You can modify a corner by using a chamfer command. This will create a 45-degree angle at the apparent intersection of the corner.
- Click the Corner Editor icon.
- Select the corner to be angled. In this example we are using the example image 4 above.
- In the Visual Wall Corner Editor dialog, select Chamfer (angle).
- Enter the interior length of the angled wall.
- Look at the preview in the dialog.
- Click Apply.
Joining Walls at Corners
Another way that two non-intersecting walls can be joined is by using the Join Walls icon.
- Click on the Join Walls at Corner icon from the Edit section of the Walls sidebar.
- With the cursor, select the ends of the two walls you want to join as a corner.
Trim Walls
- Click the Trim/Extend icon from the Edit section of the Wall sidebar.
- Click the wall that will be cut to.
- Click on the wall to be trimmed off.
- Use repair wall tool under the Cleanup section if necessary. This tool will close any open wall gaps left over from the trim function.
Extend Walls
- Click the Trim/Extend icon from the Edit section of the Wall sidebar.
2. Click the wall to be extended to.
3. Click on the end of the wall to extend.
4. Use Cleanup if necessary.
Stretch Walls
The stretch feature allows you to lengthen/shorten an existing space as a whole.
- Click the Stretch Area icon.
- Select the wall area to stretch/shorten. To stretch an entire room, the end of the room must be selected.
- In the Stretch dialog box, enter an X or Y value.
- Click the directional arrow to ensure it is pointing in the correct direction for the distance you want to stretch.
- Click Perform Stretch. In the example image below, you can see on the left the selection we made, that we needed to stretch that end of the room 2 additional feet to the right.