Stop ![]()
The Stop button ends the current operation. The ESC key also performs this function. You may also click Stop to deselect highlighted items in the drawing.
Undo
Click this button to undo past commands in your drawing. You may reverse up to 30 commands in the drawing. This function can be very useful if you discover that you made a mistake some time earlier in your drawing process: you may simply undo commands until you reach the point where you wish to start again. You may also access this function by selecting Undo from the Edit Menu. If you undo a command you wish to keep, simply click the Redo button, right next to Undo on the Toolbar.
Redo
Click Redo to reinstate commands you have removed using the Undo function. You may reinstate up to 30 undone commands.
New
Click this button to create a new drawing. If applicable, you will be prompted to save the existing drawing.
Open
Click this button to open an existing drawing without having to go through the File menu. Choose Open to open a drawing, Typical, DXF file, DWG file, defaults file, view file, bitmap image file, color map file, or Hidden Line file.
Save
Click this button to save the current drawing without having to go through the File menu. Use the Save command to save your drawing with a .cdb extension. If this is a new drawing, the Save As dialog appears and you are prompted for a name for the drawing.
Check and Save
Click this button to run a Drawing Integrity Check before saving. The Drawing Integrity Check dialog appears, allowing you to check your drawing for various problems. When the check is complete, the drawing is saved or, if not previously saved the Save As dialog appears.
Import/Export/Style Files
Click this button to load and save styles and special files.
Print
Click this button to access the Print function without having to go through the File menu. The Print Drawing dialog appears, or the Print dialog if a Render window is active.
Print Preview
This function shows you an approximate image of what your print will look like. The magnifying glass function allows you to zoom in and examine areas of the potential print image.
Set Options
Click Set Options to bring up the Options dialog, where you may set your preferences for Giza.
Load Help System
Click this button to access the help file.
Activate 2D Window
Click this button to switch focus to the 2D window. A new 2D window is created if none currently exists.
Activate 3D Window
Click this button to switch focus to the 3D window. A new 3D window is created if none currently exists.
Create Hidden Line
Click the Create Hidden Line button to execute a Hidden Line Drawing. A Hidden Line drawing (a black and white 3D view with solid faces) of the current 3D drawing window is generated. If the Hidden Line process is already in progress, an error message is displayed.
This process may take some time on larger drawings, and prompts indicating progress appear in the status line.
Render 3D Window
Click the Render 3D Window button to execute a Full Color Shaded Rendering. The Rendering process is invoked to create a shaded image of the current 3D drawing window. If the Render process is already in progress, an error message is displayed. This process may take some time on larger drawings, and prompts indicating progress appear in the status line. The Render tab of the Options dialog (called from the Tools menu) is used to set up rendering parameters.
Select Window
Click Select Window to choose an active window. This is a convenient function if you prefer to have windows maximized but keep more than one type of window open. The Choose Window dialog appears, showing you a list of the windows you have open. Click the desired window, and it is brought to the top.
Redraw Window
Click the Redraw Window button to redraw the current drawing window. This function is useful for redisplaying the drawing when you have made changes, especially erasing, that may not be properly visible until the screen is redrawn.
Zoom All
Click the Zoom All button to zoom the drawing window so that all items in the drawing fit into the view. The scale of the view in the current window is recalculated so that all elements in the drawing fit within the display window. Elements in layers, which are not on for display, are not included.
Zoom Area
Click the Zoom Area button to zoom in on an area of the drawing window. You are prompted to define the corners of a rectangular area, which then fills the window. The scale of the view is adjusted so that the area selected fits just within the display window. The rotation of the view is not affected.
Zoom In ![]()
Click the Zoom In button to make items displayed in the current window appear larger. The scale of the view in the current drawing window is increased. The rotation of the view is not affected. The amount the view scale is increased can be configured on the View Setups dialog.
Zoom Out
Click the Zoom Out button to make items displayed in the current window appear smaller. The scale of the view in the current drawing window is decreased. The rotation of the view is not affected. The amount the view scale is decreased can be configured on the View Setups dialog.
Rotate View
Click one of the two Rotate View buttons to rotate the view in the current drawing window either counter-clockwise or clockwise. The View Control dialog provides additional controls for adjusting the view in different directions.
Swap View
Click the Swap View button to Swap between the current view and the last view.
Perspective Camera
Click the Perspective Camera button to bring up the Perspective Camera icon. The camera icon appears, and a Perspective view window is added to the drawing. Manipulate the camera icon to control the contents of the Perspective window.
The Camera dialog also appears where you may set parameters for the Perspective Camera.
Birdseye View
Click Birdseye View to bring up a Perspective window, showing a Birdseye view of the drawing.
View Control
Click this button to bring up the View Control dialog, allowing you to set the view.
The View Control dialog provides controls for manipulating the display in the current drawing window. Standard view angles can be selected. Incremental rotation around the view or the drawing axes can be performed. View scale can be increased or decreased. View control parameters can be modified.
Vignette Print
Select this button to create a Vignette print of your drawing. The Print Vignette Sheet dialog appears, allowing you to set the parameters for plotting your drawing.
Publisher
Publisher is an application within Giza designed to allow you to print detailed reports, complete with illustrations of your drawings, in a layout and format you control. For more information on Publisher and how to use it, see the Publisher chapter.
Furniture Placement
Click the Furniture button to display the current furniture product line menu. This button has been added so that you may go directly to furniture placement if you are in another mode, such as 2D Drawing.
Select Symbol
Click the S button to bring up the Select dialog, where you can search and place symbols by part number. You may use this function to place a symbol without having to locate it on a library menu.
Panel Placement
Click the Pnl button to bring up the Panel Placement dialog, where you may place panels automatically. You may also access this function from the Draw menu.
Frame Designer
Select Frame Designer to bring up the Frame Designer dialog, where you may apply frame designs to panels in your project. See the Frame Designer section for more information.
Draw Walls
Click this button to activate the Wall Drawing application. This button has been added so that you may go directly to Wall Drawing mode, without having to go through the Draw Menu.
Draw CAD
Click this button to activate the 2D Drawing (CAD) application. This button has been added so that you may go directly to drawing mode, without having to go through the Draw Menu.
Add Image
Select Image to bring up the Add an Image dialog. Here, you can select a .bmp or .jpg image and place it in your drawing.
Point Input
Click this button to bring up the Point dialog. This dialog allows you to enter exact X (horizontal) and Y (vertical) distances, used in many Giza functions.
Set Snap and Reference
Click this button to activate the Snap/Set Reference dialog. When using the status line for distance input, the relative distance is measured from the reference point, which is usually the last point entered. To set a different reference point, click the Set Reference button, and then enter the new point. Several different references (Midpoint, End Point, etc.) are available. See the Point Input section for more information. This command may be executed in the middle of another command—such as running line—to set a reference point and then continue with the previous command.
Measure Distance
Use this function to measure distances or items in your drawing. Click on the start and finish locations of the length you wish to measure. You may right-click to snap to the corner of an item you wish to measure, to ensure an exact measurement. The Measure Distance dialog appears and displays the length measured, the horizontal and vertical distances, the elevation and the angle of the area defined. This function is also available under the Tools Menu.
Note: It is recommended that you measure items without the Ruler function (on the Lower Status Bar) enabled, as the Ruler can affect measurements in the drawing.
Special Symbol Creation
Select Special Symbols to launch Giza Specials, which contains special functions to create and modify custom furniture symbols for Giza.
Worksheet
Click this button to launch Worksheet. Worksheet allows you to determine the cost of all the items in your drawing and generate pricing reports. For more information on how to use Worksheet, access the help system after you have launched Worksheet.
Update from Visual Worksheet
To update the current drawing with any finish changes made in Worksheet or Visual Impression.
Create Scene Bound
To organize your drawing into scenes around different points of interest that you want to call attention to when viewing in Visual Impression.
Manage Scenes
To add or delete a scene for Visual Impression.
Visual
To open Visual Impression and render your currently opened drawing.
Media Program
(Legacy) Click Media Program to open the Media Program application, which allows you to access pictures of Giza furniture and layouts. If there are Typicals associated with these pictures, they can be placed in your drawing.
Inventory
Click the Inventory button to access the Inventory comparison application. Inventory allows you to compare two projects. This gives you the option of reusing furniture components, reducing the number of new components you must purchase.
Load Layer Dialog Box
This button brings up the Layer Selection dialog, where you can select a work layer, and turn layers on or off for display in your drawing. This function is also available from the Layer button, located in the lower left of the Giza Design 2004 screen. See the Status Bars chapter for more information on this dialog.
Material Assignments
When you select Material Assignments, the Material Assignments dialog box appears. From here you can set colors for or apply image textures to various surfaces.
Layer Setup
This button brings up the Layer Selection dialog, where you can select a work layer, and turn layers on or off for display in your drawing. This function is also available from the Layer button, located in the lower left of the Giza screen.
Current Color
To change the color, click the button. The Select Color dialog appears. Click the color you want, and click OK. If you wish to modify a color, double click it to bring up the Color to Modify dialog.
Pen
This dialog appears when you click the arrow next to the Pen box on the Lower Status Bar. Pens are used to display lines differently in the drawing. To change the current pen type, select a pen from the list and click OK.
XY Forcing
Check XY to enable XY Forcing in your drawing. This makes it so that all lines or walls you draw are forced to be at 90 degree angles to one another (in general, this is true vertical and horizontal).
Ruler
Turn the Ruler on to force placement of elements to conform to the increment set for the Ruler. This increment is set on the Input tab of the Options dialog, located on the Tools menu. The default Ruler increment is 1'-0".
Work Angle
Click the Work Angle button to bring up the Set Work Angle dialog, where you may control your drawing angle.
Snapping
If this box is checked, the symbols you place are snapped to the nearest existing item in the drawing when clicking with the left button. If Snapping is not checked, furniture items you place are rounded, but not snapped to existing items except when right-clicking.
3D modes
The status bar placement options help you determine how symbols are placed in the Z plane. Click the button next to a placement mode to select it.
Norm. Used for placing symbols on the floor of your model (without a Z Height). If default library elevation settings are in place for specific furniture items, they are placed with these defaults rather than on the floor.
Surf. Use the 3D surface placement mode when you wish to place symbols on top of one another: for example, when you are placing desktop items. If you try to place a phone on top of a desk without first selecting 3D Surface, the phone is placed on the floor instead of on the desk. You may also set a specific Z Height, but 3D Surface is useful because you need not know the exact height of the desk to place a phone on it. Remember to switch back to Normal after you are done placing these type of items.
Z Ht. Use the Z Height mode to set symbols a specific distance above the floor of your model. Use the arrows to the right of the box to change the value or enter a value directly.
When you are finished placing symbols with Z height, remember to return to Normal placement mode.
Note: The Walls toolbar becomes visible only when the walls sidebar is active.
Height
Enter the height for the walls in the box. You may enter the value directly or use the increment arrows. Any walls you draw are of the height entered here.
Width
Enter the width for the walls in the box. You may enter the value directly or use the increment arrows. Any walls you draw are of the width entered here.
Justification
The justification set for the walls appears here. To change the wall justification, click the arrow button to bring up the Wall Justification dialog. You may also set justification on the Wall Parameters dialog, reached by clicking the green clipboard icon on the Walls Tab menu.
Auto Snap
Check this box to enable wall snapping. This mode snaps new walls to the closest existing wall, within the Auto Snap tolerance. This tolerance is set on the Wall Parameters dialog, which you may access by clicking the green clipboard icon on the Walls tab menu.
Create 3D
Check Create 3D to have walls drawn as 3D symbols in the 3D drawing window as each wall is drawn. Otherwise, walls appear as 2D lines. Walls can be remade, from 2D to 3D and vice versa, after they are established.
Slope
Check this box to enable wall slopes. This allows a wall to be placed with different end heights. Enter the other height in the End Ht box.
End Ht
Click End Ht to set the end height of the wall. Use the arrows, or enter a value directly.
Check for software updates
Checks for any available software updates.
Check for catalog updates
Will show any pending updates to your currently installed manufacturer catalogs. You can then choose to install those updates.
Catalog Center
Use the catalog center to manage your manufacturer catalogs. Catalog Center allows you to install, update, and remove manufacturer catalog content.
Website
Click to go to the Giza Knowledge center
Community
Find support contact information
Feedback or Wishlist
Use this to send an email to product management to communicate any general feedback you have about the software or to submit a feature request. This should not be used for technical support. If you need help, please contact the support team.
Knowledge Center
Visit the knowledge center website.
Live Chat
Get help from the AI assistant or chat directly with a support agent.
Email Us
Send an email to support.
Remote Support
Allows downloading the TeamViewer client that support may ask you to use to connect to your PC for direct assistance.
New Catalog Request
If you know of a manufacturer catalog that is not available for Giza, use this button to send us an email to alert us. Our data team will reach out to that manufacturer to explore if they would be interested in partnering with us to make their catalog available on our platforms.
Training
Explorer training options available from our website.
Help
View helpful Giza articles on the support center.
Social Media
Use these icons to visit us on Facebook, Twitter, LinkedIn, YouTube, and Instagram